Tips for Adjusting Your Hot Water Heater Settings

No comments

Though many home owners never do so, it is possible to adjust the temperature of your hot water by adjusting your hot water heater settings. If you find that the water throughout your home is too hot, or not quite hot enough, you can decrease or increase the temperature slightly to make it more comfortable. Or, if you’d like to save on your energy bills, you can reduce your hot water temperature by a few degrees to start seeing an impact.

Changing your hot water heater settings too much can result in water that is scalding hot, so remember to test the temperature after each minor adjustment you make! The following are our top tips for adjusting your water heater safely and easily:

  • The recommended temperature for your water heater is 120 degrees Fahrenheit, and this is the default temperature that most water heaters are set to when installed. If your water seems a little too hot or too cool, check the current temperature and adjust it accordingly.
  • Gas water heaters usually have a knob to adjust the heat setting. It’s important to note that turning the dial to the left will increase the temperature, while turning it to the right will decrease the water temperature.
  • If you have an electric water heater, you may need a few tools like a screwdriver or wrench to adjust your hot water heater settings. First, turn of the circuit breaker and remove the access panels. Find the thermostat and use a flat head screwdriver to adjust the knob to your desired temperature.
  • After any adjustment, run a faucet on the hottest setting for one minute. Fill a cup with a few inches of this water and use a cooking thermometer to determine the actual temperature of the water. Wait about 30 seconds for an accurate reading.
  • Hotter temperatures are more effective at killing bacteria (making your dishwasher and laundry more effective) but can scald younger children or the elderly during bathing. Consider the needs of your household before raising the temperature of your hot water heater.
  • If you get no hot water at all after adjusting the thermostat, you may be dealing with a larger issue. The hot water heater’s heating element may be malfunctioning and requires replacement, which can be done with the help of a technician.

A professional water heater technician can adjust the settings of your water heater, so we suggest calling in an expert water heater repair specialist if you don’t feel comfortable with a DIY approach. Schedule an appointment with Evam Canada online today or call 1-905-624-5544 to have a hot water heater professional change your settings.

Evam CanadaTips for Adjusting Your Hot Water Heater Settings
read more

How to Replace a Hot Water Heater Thermocouple

No comments

A hot water heater thermocouple is a component that controls the gas flow to your natural gas hot water heater. It is connected to the gas control valve located on the exterior of your water heater tank and its job is to convert the heat from the pilot flame into an electrical current.

When the thermocouple does not sense a flame, it stops the gas valve from delivering gas to the burner altogether. Your water heater stops delivering hot water to you home since it has no way to heat the water. Unfortunately, issues with the hot water heater’s thermocouple can be the reason why your pilot light is not igniting or the burner is not staying lit.

If you believe a bad thermocouple is the reason why your pilot light won’t stay lit, you can replace the component fairly easily with a few tools and a replacement thermocouple. Most thermocouples are universal, but if you aren’t sure, disconnect the existing thermocouple and take it to the hardware store to ensure you’re getting the right part.

If you’re up to this DIY hot water heater repair, here are our tips on how to replace a hot water heater thermocouple:

  1. Turn off the gas supply. Before you begin any repairs, ensure that the gas control knob is in the “OFF” position.
  2. Remover the cover from the exterior of your hot water heater. If there is a cover over the burner compartment, remove it. Unscrew the pilot tube and the thermocouple line from the burner assembly using an adjustable wrench.
  3. Remove the burner assembly from inside the water heater. There may be clips holding the old thermocouple to the pilot gas supply tube which you will need to disengage.
  4. Install the new thermocouple in the same way you removed the old one, inserting the probe into the fitting and the other end into the pilot gas supply.
  5. Reinstall the burner assembly into the and use the wrench to reconnect the burner, pilot and thermocouple tubes.
  6. Place any covers that you have removed back onto the unit.
  7. Turn on the gas valve and check the lines for any leaks. Apply soapy water to any connections and watch for bubbling. If you detect a leak, shut off the gas immediately and contact a professional water heater technician for assistance.

Not comfortable replacing your thermocouple on your own? Evam Canada’s skilled hot water heater technicians are here to help repair and maintain your equipment. Contact us online today to schedule your repair appointment or give us a call at 1-905-624-5544.

Evam CanadaHow to Replace a Hot Water Heater Thermocouple
read more

Why is My Hot Water Heater Leaking?

No comments

When you discover a pool of water surrounding your hot water tank, it can be the result of your hot water heater leaking – but don’t panic. Your next step should always be to turn off the power to your water heater so you can safely begin identifying the source of the leak.

If you have a gas water heater, look for the on/off switch and turn it to the “off” position to shut the unit down. If you have an electric hot water heater, find the breaker for your water heater at the circuit breaker box and switch it off.

Now you are ready to determine why your hot water heater is leaking and how you can stop it. In this article, we will outline the most common causes of hot water heater leaks to help you identify your specific problem.

  1. Water Supply Line Leak
    If you find that water is leaking from the lines that supply water at the top of your hot water heater, you should first shut off the water supply to your home to prevent further leakage. Fixing this type of leak could require a simple tightening of the connections or may require total replacement of the supply lines.
  2. Leaking Temperature and Pressure Relief Valve
    Water can sometimes leak from the temperature and pressure relief valve (T&P), which is a feature integrated into your water heater to release excess pressure when detected. A leak from this area may mean the valve is defective and requires replacement, which should be performed immediately for your safety.
  3. Drain Valve Leak
    A leak at the drain valve near the bottom of your water heater may mean your drain valve is not completely closed or is faulty, and often happens after your water heater has been flushed or drained. The drain valve can be replaced by a professional, who will shut down your water heater and drain it completely to perform the repair.
  4.  Hot Water Heater Leaking from Tank
    If you’ve ruled out the above sources of leaks, it is highly likely that the hot water tank has developed a leak over time due to age and deterioration. Unfortunately, a leaking tank cannot be repaired and requires complete replacement. A water heater expert can help you choose a new unit that suits your needs.

Need a professional to solve your hot water heater leaking problems? The knowledgeable technicians at Evam Canada are here for all your water heater repair needs. We also offer one-time and regularly scheduled water heater maintenance plans to help you prevent leaks and other problems before they happen.

To schedule a repair or maintenance appointment, call 1-905-624-5544, or contact us online.

Evam CanadaWhy is My Hot Water Heater Leaking?
read more

What to Do if Your Hot Water Heater is Not Heating

No comments

When your hot water heater is not heating, your daily tasks like showering, washing dishes or doing laundry can be unpleasant. Hot water is an important part of our routine, and a disruption in your supply can really impact your day. You’ll probably look for the best way to get your hot water back up and running as soon as possible so you can enjoy a more comfortable water temperature.

Should you discover that your hot water heater is not heating water properly, try the following steps to address this common water heater problem:

  1. If you have an electric hot water heater, check to see if the circuit breaker has been tripped. Reset the breaker at the breaker box if this is the case to restart your water heater.
  2. Determine if the pilot light is out if you have a gas water heater. If it needs to be re-lit, consult your water heater owner’s manual for instructions.
  3. In gas water heaters, you can examine the gas supply valve to see if it is shut off or is damaged in any way. We highly recommend that you have an HVAC technician repair your gas supply valve if you suspect it is the cause of your hot water heater not heating.
  4. Check the thermostat to see if the temperature is set too low. The recommended temperature setting is typically around 120 degrees Fahrenheit, so adjust the dial to a higher setting if you find it is below the 120-degree F mark.
  5.  See if the temperature and pressure relief valve is open or defective. When excessive water temperature is detected or extreme pressure builds up inside the water heater, this safety feature will shut off the unit entirely. A professional should be called to examine your water heater if this is the case.
  6. Consider draining your water heater tank to get rid of any sediment that has collected at the bottom of the tank. This buildup can impact the functioning of your hot water heater and over time, can deteriorate the inside of the tank itself.
  7. Contact an experienced water heater technician to troubleshoot and resolve the problem. If you’ve exhausted the steps above and still have not restored your hot water, you need the assistance of an expert.

If you find that your hot water heater is not heating and need a trusted HVAC company to handle your emergency water heater repair, Evam Canada is here to help. We’ll work hard to get your hot water heater working properly in no time at all! Contact us today to book an appointment or call 1-905-624-5544.

Evam CanadaWhat to Do if Your Hot Water Heater is Not Heating
read more

5 Gas Water Heater Maintenance Tips for Home Owners

No comments

Did you know that gas water heater maintenance is essential to ensuring you have hot water at the ready? Many home owners don’t realize that just like a furnace or air conditioner, their hot water heater needs regular maintenance too!

Water heater maintenance is the key to a worry-free supply of hot water for your home and is an important part of preventing future water heater failures or major repairs. To maximize the lifespan of your gas water heater, we recommend that you examine it seasonally and perform a few easy DIY maintenance tasks.

Here are some quick and simple gas water heater maintenance tips that you can handle yourself to ensure your equipment is running efficiently:

  1. Keep the area around the water heater clear
    Always give your gas water heater some breathing room by ensuring there is no clutter or debris surrounding it. Gas water heaters require oxygen to burn gas, and if your unit is crowded by furniture or boxes, this can impact its efficiency.
  2. Check the temperature
    Take a look at the temperature dial on your water heater, usually located on the gas valve. Many experts recommend that your water heater is set to 115-120 degrees F to prevent overheating and to promote overall efficiency.
  3. Check for leaks
    Carefully examine the exterior of your hot water tank for any cracks, rust stains, damage, or signs of water pooling at its base. If you see even a tiny leak, you should have it repaired immediately to prevent further damage and increased utility bills.
  4. Drain your water heater
    Use the drain valve to drain a few gallons of water from the tank using a bucket or hose to flush out debris. Keep an eye out for excessive debris or sediment in the water; If you see a lot, contact a professional to examine the tank.
  5. Test the temperature and pressure relief valve
    Your gas water heater is equipped with a temperature and pressure relief valve as a safety measure. This component detects when there are extremely high temperatures or excessive pressure buildup inside the tank and automatically opens to release pressure. To test the valve, place a bucket at the end of the discharge tube and lift the lever, allowing water to flow out for a few moments. If the valve is stuck or leaky, it should be replaced.

If you’re not sure how to approach gas water heater maintenance on your own, we recommend that you get in touch with an expert to keep your water heater in top shape. At Evam Canada, we offer gas water heater maintenance plans and regular service, along with emergency water heater repair to make sure you always have hot water when you need it.

Call us today at 1-905-624-5544, or schedule an appointment for water heater service online.

Evam Canada5 Gas Water Heater Maintenance Tips for Home Owners
read more

DIY Solutions to Common Hot Water Heater Problems

No comments

Are you experiencing hot water heater problems? Like any component of the HVAC system within your home, you hot water heater can sometimes fail to work as expected.

While hot water heater problems can be an annoyance, there are some DIY solutions you can take on to get your water heater working correctly. Below are some of the most common water heater issues experienced by home owners and how to troubleshoot them:
No Hot Water

If your water heater is producing no hot water at all, its pilot light may be out. Check to see if the pilot light is lit, and if it requires relighting, follow the instructions in your owner’s manual. If you are not comfortable relighting the pilot light, we recommend that an HVAC technician do this for you.

Water Isn’t Hot Enough

Increasing the temperature of your water is an easy fix for many home owners. Simply check your hot water heater’s thermostat. The recommended temperature is around 120 degrees F, so if it is any lower, increase the temperature. If this does not solve the problem, you may be facing issues with the heating element or have a broken thermostat, which are both repairs that need to be handled by an expert.

Not Enough Hot Water

If you’re consistently running out of hot water for showers or baths, you likely have an undersized water heater for your household’s needs. You may need a new hot water heater with a larger capacity or a tankless water heater, which produces hot water on demand rather than storing it in a tank.

Water Heater Leaks

Finding water pooled around the bottom of your hot water heater is never a good sign. Check all valves and pipe connections for the source of the leak. If none of these areas seem to be the cause of the leak, you are most likely dealing with a leak in the actual tank or another complex component that must be replaced by a water heater technician.

Noisy Water Heater

Some sounds from your hot water heater are normal and occur when metal parts expand or contract due to temperature changes. However, if you hear popping, gurgling or banging noises, they may be caused by a buildup of sediment inside the tank, which is a more serious concern. Try draining or flushing your water heater or call in a pro for help.

If you have tried these DIY tips and are still experiencing hot water heater problems, it’s time call in a professional water heater repair technician. The experts at Evam Canada are on hand to determine what is causing the problem and will repair or replace your water heater so you can enjoy warm water when you need it.

When you are experiencing any of the above common hot water heater problems, contact us to book an appointment and we’ll get your water heater running properly!

Evam CanadaDIY Solutions to Common Hot Water Heater Problems
read more